MC68000 Pinout 51,52,62,63,64

The place to ask all those likely daft questions!
zChris
Posts: 194
Joined: Fri Nov 27, 2020 10:13 pm

MC68000 Pinout 51,52,62,63,64

Post by zChris »

Hello,

I have added a socket to a Atari 520STfm and done a beeping test to see if the socket has connections. On pin 51,52,62,63,64 im not sure where to probe to see if it has connection.

On reading http://dev-docs.exxosforum.co.uk/520ST_Schematic.pdf it says that for example pin 51 goes to GLUE pin 10. But when i measure there i get no beep.

/zChris
User avatar
frank.lukas
Posts: 660
Joined: Fri Jan 19, 2018 11:52 am

Re: MC68000 Pinout 51,52,62,63,64

Post by frank.lukas »

zChris
Posts: 194
Joined: Fri Nov 27, 2020 10:13 pm

Re: MC68000 Pinout 51,52,62,63,64

Post by zChris »

Yes but should it beep when i measure between GLUE and mc68000 ?
User avatar
PhilC
Moderator
Moderator
Posts: 6016
Joined: Fri Mar 23, 2018 8:22 pm

Re: MC68000 Pinout 51,52,62,63,64

Post by PhilC »

zChris wrote: Tue Mar 23, 2021 1:04 pm Yes but should it beep when i measure between GLUE and mc68000 ?
Yes it should, address and datalines are common across the chips on the ST. Sounds like you might have a broken track?
If it ain't broke, test it to Destruction.
User avatar
frank.lukas
Posts: 660
Joined: Fri Jan 19, 2018 11:52 am

Re: MC68000 Pinout 51,52,62,63,64

Post by frank.lukas »

frank.lukas wrote: Tue Mar 23, 2021 8:53 am 51=A22
52=A23
62=D7
63=D6
64=D5

https://www.nxp.com/docs/en/data-sheet/M68000UM.pdf
st_glue.png
st_glue.png (122.08 KiB) Viewed 3431 times
zChris
Posts: 194
Joined: Fri Nov 27, 2020 10:13 pm

Re: MC68000 Pinout 51,52,62,63,64

Post by zChris »

PhilC wrote: Tue Mar 23, 2021 1:07 pm
zChris wrote: Tue Mar 23, 2021 1:04 pm Yes but should it beep when i measure between GLUE and mc68000 ?
Yes it should, address and datalines are common across the chips on the ST. Sounds like you might have a broken track?
I was in the wrong place probbing. But now when i found where GLUE is (i think i found it anyway) all pins on the socket have connections. Is the beeping test a good test to see if the connections are good enough ?

When i put in DUALTOS + Decoder board i get a white square and a yellow bar around it. With original ROMS and MC68000 in the socket it boots up in TOS.
User avatar
PhilC
Moderator
Moderator
Posts: 6016
Joined: Fri Mar 23, 2018 8:22 pm

Re: MC68000 Pinout 51,52,62,63,64

Post by PhilC »

@zChris you would probably be better off using the multimeter to measure resistance. One of mine beeps even if you have 100 ohms resistance, which isn't very useful for me.

Maybe also check pin to pin, to make sure you don't have a bridge between two pins and of course you'll need to set those rom jumpers up to use that dual tos board.
If it ain't broke, test it to Destruction.
zChris
Posts: 194
Joined: Fri Nov 27, 2020 10:13 pm

Re: MC68000 Pinout 51,52,62,63,64

Post by zChris »

PhilC wrote: Tue Mar 23, 2021 4:54 pm @zChris you would probably be better off using the multimeter to measure resistance. One of mine beeps even if you have 100 ohms resistance, which isn't very useful for me.

Maybe also check pin to pin, to make sure you don't have a bridge between two pins and of course you'll need to set those rom jumpers up to use that dual tos board.
Alright ill check with ohm. Yeah i test both positions on the jumper.
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: MC68000 Pinout 51,52,62,63,64

Post by exxos »

Have you simply tried one board at a time to see if you can rule out if it's the ROM board for the decoder board ?
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
PhilC
Moderator
Moderator
Posts: 6016
Joined: Fri Mar 23, 2018 8:22 pm

Re: MC68000 Pinout 51,52,62,63,64

Post by PhilC »

exxos wrote: Tue Mar 23, 2021 5:28 pm Have you simply tried one board at a time to see if you can rule out if it's the ROM board for the decoder board ?
That was going to be my next suggestion.

@zChris try it with the original CPU in the socket and the original rom chips, then if that works try the dual tos board with 1.04 and then finally the tos decoder board.
If it ain't broke, test it to Destruction.
Post Reply

Return to “NOOB QUESTIONS”