Still working on this and have created the Gotek or modern Floppy Drive slot to complement the short button slot. Now figuring out how this could become a panel instead of part of the complete grill section.
STFM case remake
Re: STFM case remake
Great work !
I would suggest that the whole rounded rectancle becomes a panel, you clip the one that fits your gear (short button, long button, gotek, ...)
Re: STFM case remake
Thanks @sporniket, that’s the idea to have it look seamless whilst keeping the integrity of the case structure. I am working on three options at the moment and the one that is similar to the rear panel with slots is looking the better solution at the moment. However it’s not until I tryout prototypes that I will see which is the best.
- stephen_usher
- Posts: 5680
- Joined: Mon Nov 13, 2017 7:19 pm
- Location: Oxford, UK.
- Contact:
Re: STFM case remake
Of course, that end plate is structural and gives most of the rigidity to the case.
I s'pose if the "cut out" for the different drive face plates snapped in from the front or rear, or were held in place by the drive face plate it might work, as long as it doesn't take up too much of the area, weakening it.
I s'pose if the "cut out" for the different drive face plates snapped in from the front or rear, or were held in place by the drive face plate it might work, as long as it doesn't take up too much of the area, weakening it.
Intro retro computers since before they were retro...
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
Re: STFM case remake
Something similar has already been done: https://www.atari-forum.com/viewtopic.p ... 33#p283333 so sure, why not.
- HigashiJun
- Posts: 1215
- Joined: Fri Jun 19, 2020 7:21 am
- Location: Tokyo
Re: STFM case remake
![thumb up :thumbup:](./images/smilies/thumbup.gif)
Amazing !
Re: STFM case remake
The Falcon has the full-rectangle cut out without any obvious rigidity issues. Have I misunderstood your concern?stephen_usher wrote: ↑Sun Dec 05, 2021 10:31 pm Of course, that end plate is structural and gives most of the rigidity to the case.
BW
DFB1 Open source 50MHz 030 and TT-RAM accelerator for the Falcon
DSTB1 Open source 16Mhz 68k and AltRAM accelerator for the ST
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
DSTB1 Open source 16Mhz 68k and AltRAM accelerator for the ST
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
- stephen_usher
- Posts: 5680
- Joined: Mon Nov 13, 2017 7:19 pm
- Location: Oxford, UK.
- Contact:
Re: STFM case remake
It depends upon whether there's enough material in the lower half of the side panel to provide the stiffness for the structure.
Intro retro computers since before they were retro...
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
-
- Posts: 152
- Joined: Sat Apr 03, 2021 2:08 am
Re: STFM case remake
These look great are you having them made? I know machine tooling for a production run can be very expensive but have you considered one of the large 3D printing companies that can make these using sintering instead of fdm. I haven't used any of them myself I have an Ultimaker but the sintering would look loads better and doesn't haver the setup costs.
Brian
Brian
Re: STFM case remake
@Icky built a printer to do this stuff. https://www.exxosforum.co.uk/forum/viewt ... 300#p62201 Though he is pretty much still prototyping.UnderTheRain wrote: ↑Thu Dec 30, 2021 9:20 pm These look great are you having them made? I know machine tooling for a production run can be very expensive but have you considered one of the large 3D printing companies that can make these using sintering instead of fdm. I haven't used any of them myself I have an Ultimaker but the sintering would look loads better and doesn't have the setup costs.
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.