TF1230 Compatibility
Moderators: terriblefire, Terriblefire Moderator
Re: TF1230 Compatibility
I did have a issue with the State of Art demo when testing early last month, stalling about 3/4's the way through. Did not mention this at the time as I changed to another CF card and the issue disappeared. Will try that CF card again with the new firmware when I get a chance.
Life is really simple, but we insist on making it complicated - Confucius
-
- Moderator Team
- Posts: 5389
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF1230 Compatibility
Folks this thread is for software compatibility of the TF1230. For general issues start a new thread
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF1230 Compatibility
Tried the new firmware today, could not find any issues in the demos listed, all seemed smooth as silk. Still have a issue with State of Art crashing on one of my installs, but it is only happening on one particular CF card, so it has to be an issue with that CF card.
Test rig: 2B Motherboard, custom extended 31 ROMs, TF1230 onboard IDE used.
Edit:
Any other particular tests required About to start some repair work on a 3000 and the 1200's will be shelved in the next few days.
Test rig: 2B Motherboard, custom extended 31 ROMs, TF1230 onboard IDE used.
Edit:
Any other particular tests required About to start some repair work on a 3000 and the 1200's will be shelved in the next few days.
Life is really simple, but we insist on making it complicated - Confucius
Re: TF1230 Compatibility
@Danoo
Can you confirm the two issues below are resolved during your tests? They are still present on my test setup.
Cuzco / Oxygene - artifacts on screen during cube / cheese display.
Drool This / Parallax : (can be found in supaduper's archive) With the latest firmware, starts and runs then Gurus the machine about 5 seconds into rendering the "3D FPS room" section near the start of the demo. The same behaviour is shown in the video at 4:12. This one seems to run OK on WinUAE.
@PaulJ_2.0 Are you still unable to get the card to boot with the new firmware on your 2B?
Can someone else with a 2B and a 1230 test this?
Can you confirm the two issues below are resolved during your tests? They are still present on my test setup.
Cuzco / Oxygene - artifacts on screen during cube / cheese display.
Drool This / Parallax : (can be found in supaduper's archive) With the latest firmware, starts and runs then Gurus the machine about 5 seconds into rendering the "3D FPS room" section near the start of the demo. The same behaviour is shown in the video at 4:12. This one seems to run OK on WinUAE.
@PaulJ_2.0 Are you still unable to get the card to boot with the new firmware on your 2B?
Can someone else with a 2B and a 1230 test this?
Re: TF1230 Compatibility
@go0se
Oxygen yes flickers at cheeses then scarab beetle zoomer.
Drool This / Parallax - works fine. I downloaded it elsewhere. From Demozoo?
Oxygen yes flickers at cheeses then scarab beetle zoomer.
Drool This / Parallax - works fine. I downloaded it elsewhere. From Demozoo?
Re: TF1230 Compatibility
No still no booting, I tried a second card with a diff spec -5 CPLD and no boot.
I will dig out another board revision to check later.
Re: TF1230 Compatibility
Cheers.
Interestingly, the version of Drool This available on Demozoo/Scene.org has a text note attached which reads
Interestingly, the version of Drool This available on Demozoo/Scene.org has a text note attached which reads
Which sounds like it might not be present on the WHDLoad version I was testing or the one shown on the video. I will check this version shortly.This is fixed version of the our demo that was released at the
Assembly '94. Now it is as it should have been. Wolf-routine has
a little bug that crashes the machine sometime. Enjoy the Demo.
- 8 Bit Dreams
- Moderator Team
- Posts: 785
- Joined: Fri Nov 09, 2018 7:12 am
- Location: Germany
Re: TF1230 Compatibility
Hi!
Can confirm following bugs:
Cuzco / Oxygene - artifacts on screen during cube / cheese display.
Drool This / Parallax
also got one report from a user:
Nitro - Game has garbage on the screen,
also
3DDemo2 - has some graphical glitches:
should be:
can someone please check:
Can confirm following bugs:
Cuzco / Oxygene - artifacts on screen during cube / cheese display.
Drool This / Parallax
also got one report from a user:
Nitro - Game has garbage on the screen,
also
3DDemo2 - has some graphical glitches:
should be:
can someone please check:
Retro computer hardware & repair in Germany
Re: TF1230 Compatibility
@8 Bit Dreams
Nitro looks fine. I am using WHDLoad v1.3 released March 2021.
3D Demo 2 - I am seeing the same. (Handy you can keep mouse clicking to get to the end!)
Nitro looks fine. I am using WHDLoad v1.3 released March 2021.
3D Demo 2 - I am seeing the same. (Handy you can keep mouse clicking to get to the end!)