Okay, starting my build by updating one of my H4 boards to add a PLCC52 socket, removed the 68901 DIL IC and testing the 68901FN PLCC chips I ordered.
All tested and working fine so decided to leave one in the newly installed socket.
BOM components all ordered and arrived. Just waiting on the post for the H5 boards.
kodak80 H5 A3 builds
kodak80 H5 A3 builds
Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Re: kodak80 H5 A3 builds
Whilst others have began the race to build the B1 boards, I have 6 of the H5 A3 boards so I have started building the first one to get this up and working.
First photo of IC22 Reset IC in situ before soldering:
PLC52 SMT socket soldered into place:
IC6 removed, tracks cut and re-seated using my heat gun. Fix applied:
Fix 1 applied underneath board:
First photo of IC22 Reset IC in situ before soldering:
PLC52 SMT socket soldered into place:
IC6 removed, tracks cut and re-seated using my heat gun. Fix applied:
Fix 1 applied underneath board:
Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Re: kodak80 H5 A3 builds
Thanks for confirming @Icky. I could not find anyone photos on H5 boards already built by the group so far but checked my H4 and the tracks helped even though the IC is now rotated compared to the H4.
Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Re: kodak80 H5 A3 builds
So, I may have filed too far on the "SIDE0 FLOPPY SHORT FIX" and I have cut the next track above and may have cut the other 2 tracks above that. Can anyone confirm what the other 2 tracks connect on the board so I can test continuity of these other 2 tracks?
I was testing continuity from GND to the floppy pin 32 and filed straight up. It was only when I filed to the left that the continuity stopped but by that time, I had cut the same track as exxos. I suspect I may have also cut the other 2 tracks above.
I was testing continuity from GND to the floppy pin 32 and filed straight up. It was only when I filed to the left that the continuity stopped but by that time, I had cut the same track as exxos. I suspect I may have also cut the other 2 tracks above.
Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Re: kodak80 H5 A3 builds
@kodak80 - I did the same and cut too many.
Let me find out the tracks for you.
Let me find out the tracks for you.
Re: kodak80 H5 A3 builds
Thank you. Will be good to see how much I broke...and needs fixing.
Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Re: kodak80 H5 A3 builds
I am pleased to advise, I only seem to have cut the 2nd track. Tracks 3 and 4 pass continuity test. Phew. Only 1 long bodge wire to add and the original fix wire on this board.
Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Re: kodak80 H5 A3 builds
Ya know Icky, you all most fooled me! You changed the orientation of the reset chip 90 degree's from the H4 so when @PhilC soldered his on he'd get it right the first time. I was going to place it the same orientation as the H4 but luckily I checked first.
Re: kodak80 H5 A3 builds
Phil blew up 4 before he worked it out it changed Yeah never assume anything
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.