TF1230 Beta Interest (Open Source)

68030 + SDRAM + IDE

Moderators: terriblefire, Terriblefire Moderator

User avatar
arkadiusz.makarenko
Moderator Team
Moderator Team
Posts: 1208
Joined: Wed Jun 19, 2019 7:36 am
Location: Edinburgh

Re: TF1230 Beta Interest (Open Source)

Post by arkadiusz.makarenko »

Where can I find firmware?
I have almost completed building my one, just cleaning drying etc (...yes it still may take me few days to complete it)
Do not trust people. They are capable of greatness.
~ Stanislaw Lem
terriblefire
Moderator Team
Moderator Team
Posts: 5368
Joined: Mon Aug 28, 2017 10:56 pm
Location: Glasgow, UK

Re: TF1230 Beta Interest (Open Source)

Post by terriblefire »

Here is the latest i have .. it has some glitch correction for the clock.

I would recommend people do not do large PCB orders at this stage. I'm planning a rev 2.
Attachments
tf1230r1_main_top.zip
(12.67 KiB) Downloaded 145 times
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
alenppc
Moderator Team
Moderator Team
Posts: 906
Joined: Thu Nov 08, 2018 12:59 pm

Re: TF1230 Beta Interest (Open Source)

Post by alenppc »

This version does the reset flash, and then shows the yellow screen that goes back to grey and then back to yellow. The old version went straight to yellow screen and stayed there.
User avatar
supaduper
Posts: 561
Joined: Thu Nov 08, 2018 12:05 pm

Re: TF1230 Beta Interest (Open Source)

Post by supaduper »

Same as Alen I do get an IDE flash which did not happen before, then mine can go to purple screen sometimes

This is with MX roms, still boots fine on Cmorleys roms though
go0se
Posts: 403
Joined: Sun Nov 25, 2018 7:55 pm

Re: TF1230 Beta Interest (Open Source)

Post by go0se »

Behaviour seems to be different on each power on with this one. 1D.4 motherboard, 3.1 MX ROMs

Yellow/Mustard screen on power on, flicks to grey after ~4 seconds and back to yellow then grey constant.
Yellow/Mustard flicks to grey then to black and stays black (still with signal).

Still boots and runs on a 2B.
User avatar
kulamario
Posts: 237
Joined: Fri Nov 29, 2019 7:20 pm
Location: Greystones

Re: TF1230 Beta Interest (Open Source)

Post by kulamario »

This photo is for Board 1d4 kick 3.1
Reamiga start booting

20210831_221855.jpg
20210831_221855.jpg (83.7 KiB) Viewed 2494 times
chucky
Posts: 95
Joined: Sun Jan 13, 2019 8:42 pm

Re: TF1230 Beta Interest (Open Source)

Post by chucky »

terriblefire wrote: Tue Aug 31, 2021 9:21 pm Here is the latest i have .. it has some glitch correction for the clock.

I would recommend people do not do large PCB orders at this stage. I'm planning a rev 2.
It is a beta. hopefully noone makes large pcb orders of a BETA?!?
go0se
Posts: 403
Joined: Sun Nov 25, 2018 7:55 pm

Re: TF1230 Beta Interest (Open Source)

Post by go0se »

chucky wrote: Tue Aug 31, 2021 10:25 pm
terriblefire wrote: Tue Aug 31, 2021 9:21 pm Here is the latest i have .. it has some glitch correction for the clock.

I would recommend people do not do large PCB orders at this stage. I'm planning a rev 2.
It is a beta. hopefully noone makes large pcb orders of a BETA?!?
SmallBatch.png
SmallBatch.png (111.64 KiB) Viewed 2478 times

All you suckers buying dribs and drabs, go big or go home! the more you buy, the more you save!! 8-)
User avatar
arkadiusz.makarenko
Moderator Team
Moderator Team
Posts: 1208
Joined: Wed Jun 19, 2019 7:36 am
Location: Edinburgh

Re: TF1230 Beta Interest (Open Source)

Post by arkadiusz.makarenko »

Damn. My set up seems to be good one. It works OK (boots to kick screen, and passes RAM test on Amiga Tool Kit.

ReAmiga 1200 1.2, based on 1D4 donor. All chips were lifted from old board, so only passives and transistors are new)
Kickstart 3.1 EPROM.
I didn't boot to Workbench as my CF is configured for TF1260, so need to create new one to test this 100%.
I may try my old 3.0 MX kicks later today.
Do not trust people. They are capable of greatness.
~ Stanislaw Lem
User avatar
GadgetUK164
Posts: 430
Joined: Fri Jan 04, 2019 2:26 pm

Re: TF1230 Beta Interest (Open Source)

Post by GadgetUK164 »

Sorry if this is an obvious question - about to order the IC's, I dont see them mentioned on the bom XLS files? Is it just the same ICs used with the 536?
My YouTube Channel - www.youtube.com/GadgetUK164
Post Reply

Return to “TF330”